欢迎访问建材网!
热线电话:400-888-5105

当前位置: 首页 >建材>功能建材>防水材料 >江苏8毫米耐力板 厂家设计、加工、定做

江苏8毫米耐力板 厂家设计、加工、定做

起批量
1平方米

产品属性

品牌
其他
型号
1.22 1.56 1.82 2.1
不透水性
国标
产地
其他
材质
其他
形态
其他
等级
AAAA
吸水率
国标
断裂伸长率
90%
撕裂强度
国标
柔度
国标
导热系数
国标

  阳光板安装事项

  (1)一定要注意为阳光板热胀冷缩而留出安装间隙。阳光板的线性膨胀系数是6。75*10^(-5)m/(m*k),即温度每升高1摄氏度,1m*1m的板沿长度和宽度方向各膨胀0。0675mm。相应的,温度每降低1摄氏度,板材亦收缩相同的量。用户须根据工程所在地的四季温差,算出预留的安装空隙。{TodayHot}例如,北京地区,板材表面温度差约为80摄氏度,则1m*1m的板材安装预留间隙为:0。0675*80=5。4mm

  (2)阳光板传统安装方法分为: *干式装配法:此方法需在铝型材中穿入密封胶条。胶条材质选用EPDM或氯丁橡胶,绝对禁止使用聚氯乙烯(PVC)的密封胶条。胶条硬度以肖氏65为宜,表面平整,断面形状一致,无损伤,无变形,不发硬,有弹性。*湿式装配法:此方法要选用与阳光板材质想适应的不硬化、低模数、中性或酸性密封胶。阳光板与连接件间密封胶的延伸度要>=50%,要确保阳光板热胀冷缩及风压位移时,胶层不会因拉断产生间隙而造成渗漏。

  (3)现在改良后的阳光板安装方法分为"专用铝型材装配法"和"扣盖型装配法"。此两种方法需在铝型材或扣盖钢板下压入专用防水胶带。该胶带为进口专用胶带,其规格选型应严格按工程设计要求。

  (4)使用自攻螺钉或螺栓连接铝型材,在紧固时要注意调整好各连接部位密封性的同时,还要注意不使阳光板、连接型材及紧固件本身产生形变或破坏。

  (5)阳光板安装完毕,立即揭掉保护膜。如必须继续保护板面,则应先揭掉,再重新覆盖,以避免阳光长时间直射,而产生胶转移现象。

  (6)安装前,施工组织者一定要将保护膜印上的文字说明和注意事项理解清楚,并向操作人员说明。特别要注意"哪一面朝外"的标注。

  (7)在安装阳光板时,如需常温弯曲板材,请注意阳光板厚度(d)与弯曲半径(R)的关系。 多层板 R>=175d单层板 R>=150d波纹板 R>=4000mm

  (8)阳光板厚度及安装规格的确定,与安装地区的基本风庄、基本雪载、安装高度、建筑物体型等诸多因素有关。用户在选购阳光板时,要经过科学计算,优选阳光板的厚度及规格。若在这方面有任何疑问,可随时向本公司技术部咨询

  Installation of sunshine panels: (1) Attention must be paid to the installation gap for the expansion and contraction of sunshine panels. The linear expansion coefficient of the solar panel is 6. 75 * 10 ^(-5) m /(m * k), i.e. for every 1 degree Celsius increase in temperature, the plates of 1 m * 1 m expand 0 in length and width. 0675mm. Correspondingly, when the temperature is reduced by 1 degree Celsius, the sheet shrinks by the same amount. Users should calculate the reserved installation gap according to the four seasons temperature difference of the project location. For example, in Beijing, the maximum temperature difference on the surface of sheet metal is about 80 degrees Celsius, and the reserved clearance for the installation of 1m*1m sheet metal is 0. 0675*80=5. 4 mm (2) The traditional installation method of sunshine panel is divided into * dry assembly method: this method needs to insert sealant strip into the aluminium profile. EPDM or chloroprene rubber is used as the material of the rubber strip. It is absolutely forbidden to use the sealing tape of polyvinyl chloride (PVC). The hardness of the rubber strip should be Xiao's 65. The surface is flat, the cross-section shape is identical, there is no damage, no deformation, no hardening and elasticity. * Wet assembly method: This method should choose non-hardening, low modulus, neutral or acidic sealant suitable for sunshine panel material. The elongation of the sealant between the sunshine plate and the connecting parts should be > 50%. It is necessary to ensure that the sealant layer will not leak due to the breakage of the gap when the sunshine plate expands, contracts and displaces under the wind pressure. (3) The improved installation methods of sunshine panels are divided into "special aluminum profile assembly method" and "button-type assembly method". These two methods require special waterproof tape to be pressed under the aluminium profile or clasp plate. The tape is imported special tape, and its specifications should be selected strictly according to the requirements of Engineering design. (4) When using self-tapping screw or bolt to connect aluminium profiles, attention should be paid to adjusting the sealability of the connecting parts, and at the same time, attention should be paid not to make the sunshine plate, the connecting profiles and the fastener itself deform or destroy. (5) When the sun panel is installed, the protective film shall be removed immediately. If it is necessary to continue to protect the surface of the panel, it should be removed first, and then re-covered to avoid long-term direct sunlight, resulting in glue transfer phenomenon. (6) Before installation, the construction organizer must understand clearly the written instructions and precautions on the protective film seal and explain them to the operators. Special attention should be paid to the label "which side is facing the outside". (7) When installing sunshine panels, if it is necessary to bend the panels at room temperature, please pay attention to the relationship between the thickness (d) of sunshine panels and the bending radius (R). The determination of the thickness and installation specifications of multi-layer board R >= 175d single-layer board R >= 150D corrugated board R >= 4000mm (8) sunshine board is related to many factors such as basic manners, basic snow load, installation height and building shape in the installation area. When choosing and purchasing sunpanels, users need to go through scientific calculation to optimize the thickness and specifications of sunpanels. If you have any questions in this regard, you can always consult the technical department of our company.


规格参数
型号 1.22 1.56 1.82 2.1   不透水性 国标  
等级 AAAA   吸水率 国标  (%)
断裂伸长率 90%  (%) 撕裂强度 国标  (Mpa)
柔度 国标   导热系数 国标  
耐热度 国标  (℃) 适用温度 国标  (℃)
用途 隔热 阻燃   包装规格 牛皮纸  
品牌 拜耳   产地 河南  
材质 PC   形态 溶液状  
厚度 可定做      
包装参数
体积(m²) 0
产品重量(kg) 0
代理商供货
退换货规则说明
申请方式

1,在线申请:您可以在"我的订单"中找到您需要退换修的订单,点击”申请退款/退货”即可。我们的工作人员会在2个工作日 内和您取得联系,你可以随时在线查看你的退换修状态。

注意事项

1,“7天无理由退换货”适用于买家在收到货品后因不满意货品希望退换货的情形。

2,因质量问题产生的退换货,邮费由平台供应商承担(此质量问题为货品破损或残缺)。非商品质量问题的退换货,应由买家承担往返运费。

3,退换货要求退换的商品在平台供应商收到时有完整的外包装、配件、标牌等;待退换的物品被用过、人为破坏或标牌拆卸的不予退换。

(1)符合退货政策的商品必须包装完整、数量准确且不影响再次销售,退货的同时必须退回相应的发票和相关文件。

(2)请对寄回的商品妥善包装,若是退换货过程中由于包装过于简单造成的物流损坏,平台供应商不承担商品完整责任。

(3)发票需单独寄送。退换货时,如涉及发票退回,请您不要将发票放在货物中一起寄送,平台供应商客服人员将和您确认发票寄送地址,避免丢失。

4,退货商品的价款到账时间因支付方式的不同而有所差异,具体应参照相关银行或支付工具的说明提示,平台供应商不对退换货费用的到账时间做任何形式的保证。

特别提醒:为避免由于商品滞留造成的经济损失,所有退换货商品,买家应在所规定之时间内发回(以物流签收时间次日起7天内为准),超过规定时间仍不能将退换商品发出的,平台供应商将不予接受该退换货商品。

联系方式
注意:1 . 使用电话联系可有效保证您的号码隐私不被泄露
          2 . 拨打后可在后台进行拨打记录查询
          3 . 成交后在会员中心确认可获得积分
联系人:孙经理 (市场部/市场经理)
电话:15136206610
给我留言
注意:1. 供应商将在24小时内给您回复,回复内容将以短信形式发送至您手机。
2. 对产品的尺寸,质量,规格,库存等方面技术问题进行咨询,我们有专人进行回复,因厂家随时会更改产品的相关信息,请以厂家实际产品为准。
咨询产品:
江苏8毫米耐力板 厂家设计、加工、定做
联系电话:
联系人:
留言详情: